The crown wheel and pinion (the “ring and pinion”, or simply “the crown”) is the gear pair inside the differential that turns the propeller shaft’s rotation into wheel rotation. It is one of the parts that fleets in our markets replace most, because overloading and poor oil kill it long before the truck is worn out. It is also one of the parts that is ordered wrong most often — because the same truck model can leave the factory with two or three different sets.
This guide explains how to read a set, how to check what you have, and what we hold in Dubai.
What the two numbers mean
A set is described by two numbers: pinion teeth × crown wheel teeth, for example 9 × 41. Divide the second by the first and you get the final-drive ratio: 41 ÷ 9 = 4.56. Some catalogues print the ratio (4.56, 4.88, 5.83); most workshops and importers in our markets order by the tooth count, so that is how we list them.
- A higher ratio (more crown wheel teeth per pinion tooth, e.g. 7 × 45 = 6.43) gives more pulling power and a lower top speed — typical for a loaded truck or a mountain route.
- A lower ratio (e.g. 10 × 41 = 4.10) gives a higher cruising speed and lower engine revs — typical for a pickup used on the highway.
Both can be fitted to the same model. That is why “crown wheel for Hilux” is never enough information.
How to check what you have
- Count the teeth. Take the differential cover off (or look at the old set on the bench) and count the crown wheel teeth and the pinion teeth. Count twice — a 41 and a 43 look the same at a glance.
- Look for the stamped numbers. Most crown wheels have the tooth count stamped on the back face (e.g. “41-9” or “9/41”), often with a batch number. Pinions are stamped on the head or the shank.
- Check the pinion spline. On some sets the same tooth count exists with different pinion spline counts (e.g. 22 T, 32 T) to match the flange. If you are replacing the flange too, say so.
- Front or rear? On 4×4 vehicles the front and rear sets usually share the ratio but are not the same part. A Land Cruiser 80 rear 10 × 43 and front 10 × 43 are two different numbers.
- Send us the OE number from the old part, the tooth count, and front/rear. With those three, we can confirm the set in one message.
A rule that saves money: front and rear ratios on a 4×4 must match. If you change one axle to a different ratio, change both.
What we hold in Dubai
All sets below are MTE, made to OE dimensions and in physical stock today. Every number links to its product page; add what you need to your list and send it on WhatsApp.
Toyota Land Cruiser 70, 80, 100 and 105
- 10 × 43 — 41201-69825 front for the 70 / 100 / 105 series, 41201-80493 rear for the 80 / 105 (FZJ) and the 32-tooth-spline version 41201-80493/32T.
- 10 × 41 — 41201-69805 front for the FZJ80 / HDJ80 / HZJ80.
- 9 × 37 — 41201-69266 front for the FZJ7# / HZJ7#, 41201-69166/9*37; also 41201-69265 for the 70 / 80 with the 1HZ.
- 10 × 37 — 41201-69166 for the Land Cruiser 60 / 62.
- Pinion flanges to go with them: 41204-60050/60 and 41204-60060 for the 80 / 105, F-050.
Toyota Hilux, Fortuner, Hiace, Dyna and Stout
- 9 × 41 — 41201-29536 rear for the Hilux LN61 / LN65 / LN67 / YN50 / YN51, 41201-29536-S and 41201-09450 for the Fortuner / Hilux with 1TR-FE / 2TR-FE.
- 10 × 43 — 41201-29526 rear for the LN5# / YN52 / YN57 / YN58 / YN87 / YN92 / RN.
- 11 × 43 — 41201-09650 (R) for the Hilux / Hiace / Land Cruiser and 41201-79135 for the Hilux / Fortuner / FJ Cruiser.
- 8 × 39 — 41201-39696 rear Hilux.
- Dyna and Stout: 6 × 39 41201-39495 rear for the BU61 / BU63 / BU65 / BU80 / BU81, 9 × 37 41201-39335; pinion flanges 41204-36021, 41204-36060 and 41204-37060 for the 2F and BU30 / BU60 / BU141.
- Other Toyota: 41 × 10 41201-09060, 43 × 10 41201-09340, 13 × 31 short 41201-1360 and long 41201-1550 (ZY truck, front).
Nissan UD and Nissan Diesel
- 6 × 41 — 38110-90105, 38110-90116, 38110-90476 and 40201-1101.
- 6 × 37 — 38110-90115 and 47210-6 X 37.
- 7 × 41 — 38110-90365 and 38110-90400.
- 7 × 39 — 38110-90707 (front, RF8) and 47210-7 X 39.
- RF8 — 41201-MK001 crown wheel pinion and gear; 11 × 24 38101-90527; drive pinion gear 38686-90001 (MOK Technic) for the CWA45 / RD8.
Mitsubishi Fuso and Canter
- 6 × 41 — 12020-90040 rear for the FV313 with 8DC9.
- 6 × 40 — MC-804124 front for the FV415 with 8DC9, MC-806120 (banana type), MC-839939 for the 6D17 truck, MB-161192 and 12020-42000.
- 6 × 37 — MB-005252 for the Canter, MC-817479 and MC-835114.
- 8 × 39 and 8 × 37 — MC-834742 (16 mm, 22 T pinion spline), MC-834996/16MM (20 T) and MC-834990/16MM 8 × 37 (20 T). Note the spline count before you order.
Isuzu
- 7 × 41 — 8-98092-031-1/BLK for the NKR / NPR with 4HE1 / 4HF1.
- 10 × 31 — 9-41211-172-0.
- 6 × 39 — 1-41210-149-0; 7 × 45 — 1-41210-308-0; pinion for 1-13100-204-0 (6BG1) 1-13128-018-0.
Hino
- 7 × 45 — 41201-80209 for the HT125 / HN19, 41201-4020 and 41201-1382.
- 7 × 44 — 41201-1811; 7 × 41 — 41201-2250; also 41211-2960.
- Daihatsu Delta 11 × 37 — 41201-87615; Toyota / Daihatsu F50 39 × 11 — 41201-87613.
Fit the small parts at the same time
A new set needs new bearings, a new pinion oil seal and the correct crush sleeve and shims. We stock pinion oil seals such as 1-09625-030-0 (MOK Technic, Isuzu), 38189-90101 (Nissan CW45 / CW50) and 9828-75111 (75 × 100 × 13/18), and the matching pinion flanges listed above. Ask for them with the set — a set installed with the old seal is back on the bench within months.
How to order
Send the tooth count (or the stamped numbers), front or rear, the OE number from the old part if you have it, and the vehicle model — on WhatsApp or through your list on the site. We confirm the set the same working day, quote FOB Dubai or CFR to your port, and ship by sea or air.